Maintaining/Beautifying Wrongkos (Ways, Tips, Materials, Pitfalls)

[Bjorn]

Originally Posted by David

That would depend on the condition of the wood when i receive it.

Well noted I've found Bowling Alley Wax online so I'll give that one a try!

[David]

Originally Posted by yuuzan

Well noted I've found Bowling Alley Wax online so I'll give that one a try!

One caveat. The product i have come to like is the Butcher's product. I have been told the BWC which took over this product has kept the same formula. I don't know about other bowling alley waxes, but i think there is more than one out there.

[Bjorn]

Originally Posted by David

One caveat. The product i have come to like is the Butcher's product. I have been told the BWC which took over this product has kept the same formula. I don't know about other bowling alley waxes, but i think there is more than one out there.

I found the BWC online, so that should not be an issue. I'm also considering Birchwood Casey Tru Oil; do you have any experience with this? It seems to require quite a few coatings. How many coats does the BWC Bowling Alley Wax require?

[David]

Originally Posted by yuuzan

I found the BWC online, so that should not be an issue. I'm also considering Birchwood Casey Tru Oil; do you have any experience with this? It seems to require quite a few coatings. How many coats does the BWC Bowling Alley Wax require?

Yes, i have used Tru Oil. If i recall it is really like a finish more than something you would revitalize the wood with. I believe i put on a few coats, letting it dry in between and then took down the shine just a touch at the end with some 0000 steel wool.
With the BWC wax you cover it with a thin layer of wax, let it sit for a few minutes and then polish it with a soft cloth. It creates a really nice temporary finish that protects the wood nicely. But be prepared to pick out any globs of wax left in the crevices with a toothpick if you have a lot of carved details.

[A. G. Maisey]

The original finish on most wrongkos is french polish, ie, shellac applied with a rubber, probably a standard piano finish of upwards of 16 applications is desireable.

A shortcut is apply the shellac or varnish with brush, kill it, and rub back with rotten stone.

Tru oil will give a good "fake finish". It requires absolutely no skill in use and gives a good hard durable finish, if you want imitate the finish of an older wrongko gently take off the gloss with 0000 steel wool.

If you do not want to re-finish, but just lift the finish a bit, silicon car polish mixed with old fashinoned turps, ie, not mineral turps, and used with a rubber will get rid of the dead varnish without damaging the surface.

Danish oil can be used in a similar way to Tru oil.

If you just want to lift the finish a bit, a hand rub with baby oil will make any wrongko look about 100 times better.

A good quality furniture wax such as Antiquax will protect the finish you have created.

A "rubber" is a small square of linen or cotton cloth packed tightly with cotton wool and the ends twisted to create a little ball , you dip this into whatever you're using to load it and then you apply the finish by working in a figure of eight pattern.

When doing a complete refinish the wood should be feathered before applying the finish. The traditional way to finish wood was with a damp cloth and a hot iron, these days we use a steam iron. This raises the grain and then the wood is polished back with steel wool, you continue until the grain does not raise any longer and your final polish before application of the finish is with 0000 steel wool.

[Bjorn]

Thanks to you both, David and Alan,

Lots of useful tips!

BWC wax sounds like the easiest method. Is there any noticeable advantage to using something like Tru Oil or Danish oil, which seem to be more labour-intensive?

[David]

Originally Posted by yuuzan

Thanks to you both, David and Alan,

Lots of useful tips!

BWC wax sounds like the easiest method. Is there any noticeable advantage to using something like Tru Oil or Danish oil, which seem to be more labour-intensive?

Personally i have used Tru oil when i am doing more of a re-finishing.
As Alan says, you can create a look similar to the traditional French polish with it. If i am simply trying to maintain the current finish i will apply Butcher's wax as a final step after cleaning the piece up a bit.