Out of the box ways to clean rust?

A. G. Maisey · 19th May 2010, 08:40 AM

From what I can see of it, this blade does not look too bad at all.

Use a needle or an awl to pick the rust away, for the very small areas involved I wouldn't even use the cold blue, just a good drench with WD40 and then the usual keris oil.

I doubt that this blade needs a full clean and stain, but if it did, I would not hesitate to either do it myself or have it done commercially.

Storage in a plastic sleeve will help prevent further rusting. If you're in Indonesia, go to your local toko plastik and buy some of the plastic sleeve that is used to put snack foods in to sell in the market.Make sure its wide enough to take the gonjo.

I have preserved the original stain on a couple of Bali blades by using magnification and a needle to go over the entire blade and pick rust out of the pits and irregularities on a blade. In each case the job took about 2 or 3 months, working nights, and when I felt like it.

Cold blue may not be available in Indonesia. It is used on firearms to touch up small areas where the hot blue has worn away.

Neo · 19th May 2010, 03:29 PM

I think this is enough information to get me started. Just went to local grocery store and bought some lemon. They're out of steel wools.

I will use steel wool and WD-40 on the one with the pesi rust, and if that doesn't work I would proceed with using the lemon juice to whiten the pesi. Mr. Maisey is right, neither Ace Hardware nor Hypermart has any Cold Blue. But I guess some decent oil coating and telfon tape covering will protect the bare iron inside the ukiran for a pretty long period of time.

As for the one with some rust at the kembang kacang, I will use a needle, some WD-40, and TONS of patience ...

Kai: Sorry no additional picture for the moment (still working on some technical problems), but meanwhile you can look at this URL:
http://keris.fotopic.net/c1048837.html
Could you please explain what you meant by bold pamor? Don't you think it's the pamor is somewhat similar to the one in this URL? By the way, the sor soran part of my keris is pretty wide, quite similar to the one depicted in this URL.

kai · 23rd May 2010, 08:20 AM

Hello Neo,

Quote:

Could you please explain what you meant by bold pamor?

I was mainly referring to the high contrast between the pamor layers. Also, the pamor is tightly stacked (many layers) and pretty active.

Quote:

Don't you think it's the pamor is somewhat similar to the one in this URL?

I get your point but also see a few differences; would definitely like to see more pics for comparision before forming an unqualified opinion...

Quote:

By the way, the sor soran part of my keris is pretty wide, quite similar to the one depicted in this URL.

Yes, I see. Is this enough to base a Segaluh reference on? I admit that I keep being mystified about the tanguh game

- on one hand it seems to attempt to establish an origin in a specific time period (or even narrow it down to a specific empu) and on the other hand there seems to quite a bit of leeway possibly also including later works done in the correct style and utilizing metals of suitable characteristics... Much to learn!

Regards,
Kai

19th May 2010, 03:29 PM	#2
Neo Member Join Date: Oct 2009 Posts: 59	Thank you!! :) I think this is enough information to get me started. Just went to local grocery store and bought some lemon. They're out of steel wools. I will use steel wool and WD-40 on the one with the pesi rust, and if that doesn't work I would proceed with using the lemon juice to whiten the pesi. Mr. Maisey is right, neither Ace Hardware nor Hypermart has any Cold Blue. But I guess some decent oil coating and telfon tape covering will protect the bare iron inside the ukiran for a pretty long period of time. As for the one with some rust at the kembang kacang, I will use a needle, some WD-40, and TONS of patience ... Kai: Sorry no additional picture for the moment (still working on some technical problems), but meanwhile you can look at this URL: http://keris.fotopic.net/c1048837.html Could you please explain what you meant by bold pamor? Don't you think it's the pamor is somewhat similar to the one in this URL? By the way, the sor soran part of my keris is pretty wide, quite similar to the one depicted in this URL.

19th May 2010, 08:40 AM	#1
A. G. Maisey Member Join Date: May 2006 Posts: 7,053	From what I can see of it, this blade does not look too bad at all. Use a needle or an awl to pick the rust away, for the very small areas involved I wouldn't even use the cold blue, just a good drench with WD40 and then the usual keris oil. I doubt that this blade needs a full clean and stain, but if it did, I would not hesitate to either do it myself or have it done commercially. Storage in a plastic sleeve will help prevent further rusting. If you're in Indonesia, go to your local toko plastik and buy some of the plastic sleeve that is used to put snack foods in to sell in the market.Make sure its wide enough to take the gonjo. I have preserved the original stain on a couple of Bali blades by using magnification and a needle to go over the entire blade and pick rust out of the pits and irregularities on a blade. In each case the job took about 2 or 3 months, working nights, and when I felt like it. Cold blue may not be available in Indonesia. It is used on firearms to touch up small areas where the hot blue has worn away.