How to measure curved blades ?

fernando · 5th January 2014, 03:52 PM

I know this is a recurrent question but ...
How should i measure the length of a sword (sabre) blade ... straight from point to hilt or along the curvature ?
Also, is there a term for the curvature 'sharpness', that is, the distance of a line perpendicular to a straight between both blade ends ? Something like 'sori' in Japanese swords lexicon ?
Apparently when they talk geometricaly (?) of an arch in my language this is called 'flecha' (fletch) but, would it be acceptable to call it 'depth' in english ?
Thanks for the enlightenment .

.

Matchlock · 5th January 2014, 04:32 PM

Hi 'Nando,

Very good question

; I've often had this problem when setting up inventories for museum collections.

The same question has occurred on yahoo, and this was chosen as the best answer:
'Measure along the curve. Police will take any vagueness in the law to their advantage and will make the measurement as long as possible, so go with worst case.'

Best,
Michael

fernando · 5th January 2014, 04:45 PM

I have spotted that one too, Michl

.
But the approach in it is that of being prepared to face the law with a knife in your pocket and not one of swords tech. definitions.
Perhaps the answer resides elsewhere

.

cornelistromp · 5th January 2014, 05:48 PM

Hi Fernando,

you should messure in a straight line from point to cross(hilt) or extension of the cross so that you have a 90 degree angle there.

Fe a flamberge blade will be very long if you messure along the edge

best,

Matchlock · 6th January 2014, 10:47 AM

Hi Jasper,

I do not think that Fernando meant the slightly wavy edges of a Flamberg when he was talking about curved blades.

What I always did: I measured them both ways and mentioned the fact in the inventory.

Best,
Michael

cornelistromp · 6th January 2014, 11:51 AM

Quote:

Originally Posted by Matchlock

Hi Jasper,

I do not think that Fernando meant the slightly wavy edges of a Flamberg when he was talking about curved blades.

Best,
Michael

flamberge ? of course not, this was my (Dutch) Joke.
please see

http://japaneseswordindex.com/measure.htm

The Nagasa is the length of the blade, measured in a straight line with a 90 degree angle at the cross.
The same method is done for European curved blades.
the sori length in Europe is called THE BOW.
also the postition of the max BOW is important to describe the curve.

hope all clear.
Jasper

5th January 2014, 03:52 PM	#1
fernando (deceased) Join Date: Dec 2004 Location: Portugal Posts: 9,694	How to measure curved blades ? I know this is a recurrent question but ... How should i measure the length of a sword (sabre) blade ... straight from point to hilt or along the curvature ? Also, is there a term for the curvature 'sharpness', that is, the distance of a line perpendicular to a straight between both blade ends ? Something like 'sori' in Japanese swords lexicon ? Apparently when they talk geometricaly (?) of an arch in my language this is called 'flecha' (fletch) but, would it be acceptable to call it 'depth' in english ? Thanks for the enlightenment . . Last edited by fernando; 6th January 2014 at 01:23 PM. Reason: error

5th January 2014, 04:32 PM	#2
Matchlock (deceased) Join Date: Sep 2008 Location: Bavaria, Germany - the center of 15th and 16th century gunmaking Posts: 4,310	Hi 'Nando, Very good question ; I've often had this problem when setting up inventories for museum collections. The same question has occurred on yahoo, and this was chosen as the best answer: 'Measure along the curve. Police will take any vagueness in the law to their advantage and will make the measurement as long as possible, so go with worst case.' Best, Michael

5th January 2014, 04:45 PM	#3
fernando (deceased) Join Date: Dec 2004 Location: Portugal Posts: 9,694	I have spotted that one too, Michl . But the approach in it is that of being prepared to face the law with a knife in your pocket and not one of swords tech. definitions. Perhaps the answer resides elsewhere .

5th January 2014, 05:48 PM	#4
cornelistromp Member Join Date: Mar 2009 Posts: 1,058	Hi Fernando, you should messure in a straight line from point to cross(hilt) or extension of the cross so that you have a 90 degree angle there. Fe a flamberge blade will be very long if you messure along the edge best,

6th January 2014, 10:47 AM	#5
Matchlock (deceased) Join Date: Sep 2008 Location: Bavaria, Germany - the center of 15th and 16th century gunmaking Posts: 4,310	Hi Jasper, I do not think that Fernando meant the slightly wavy edges of a Flamberg when he was talking about curved blades. What I always did: I measured them both ways and mentioned the fact in the inventory. Best, Michael