cleaning up a wootz tulwar

shastardhari · 10th October 2017, 05:11 PM

Dear VIking sword forum,

I recently purchased a tulwar for £43, once i had it in my hands i noticed a pattern throughout the length of the blade, crystaline wootz?
i am currently cleaning it up with wd40 and fine wire wool...

some bits are very stubborn and will not come off the blade, can some suggest what else I can use to clean the blade up , and if i do use various grits of wet
and dry sandpaper how can I etch the pattern back?
here are some images of the tulwar attached

shastardhari · 10th October 2017, 08:20 PM

I used wd40 and fine wire wool to clean the blade, this is the result, what does everyone think?

Jens Nordlunde · 10th October 2017, 10:45 PM

Welcome to the forum.
What you could try is, to take some kitched issue spray it with WD40 and wrap it around the blade, then add some plastic foil, and leave it foe a day or two.
Next time you photograph, please use a neutral background.
Good luck.

Kmaddock · 10th October 2017, 11:49 PM

Hi
Welcome to the forum
I find diesel v good at penetrating rust, leave soak for a while and then clean
Here is a thread I posted a while back on etching, if you use the search forum you will find loads more information

http://www.vikingsword.com/vb/showth...hlight=Etching

Your sword looks v good and I hope the cleaned sword looks even better
Regards
Ken

mariusgmioc · 12th October 2017, 06:41 PM

More information at the link below:

http://www.vikingsword.com/vb/showthread.php?t=21732

shastardhari · 16th November 2017, 07:02 PM

Dear all
Thank you for your input.
I have cleaned the tulwar as much as I could have with the use of fine wire wool then 1200_2500 wet and dry paper. Etched using Ferric chloride.
Please tell me what you think of the end result.

Jens Nordlunde · 22nd November 2017, 04:58 PM

I think the result have cocme out fine.
I know the question, when cleaning and etching is an issue the question pops up, should I stop, or should I go further, but only the one who owns the weapons can answer that question.

shastardhari · 24th January 2018, 12:01 PM

Quote:

Originally Posted by Jens Nordlunde

I think the result have cocme out fine.
I know the question, when cleaning and etching is an issue the question pops up, should I stop, or should I go further, but only the one who owns the weapons can answer that question.

Thank you for ypur reply sir...I am happy with the results. Though there is some blCk pitting on the bladr I just can't get rid off

mariusgmioc · 25th January 2018, 08:40 PM

Hello,

I believe that in order to get rid of all the pitting you would have to polish off half of the blade. So leave the pitting as it is since is not very detracting and it also serves as an indication to the age of the blade.

You did a good job cleaning and etching the blade.

shastardhari · 29th January 2018, 04:53 PM

Quote:

Originally Posted by mariusgmioc

Hello,

I believe that in order to get rid of all the pitting you would have to polish off half of the blade. So leave the pitting as it is since is not very detracting and it also serves as an indication to the age of the blade.

You did a good job cleaning and etching the blade.

Thank you sir

shastardhari · 29th January 2018, 05:49 PM

Quote:

Originally Posted by Jens Nordlunde

Welcome to the forum.
What you could try is, to take some kitched issue spray it with WD40 and wrap it around the blade, then add some plastic foil, and leave it foe a day or two.
Next time you photograph, please use a neutral background.
Good luck.

Dear sir,

What do you mean by plastic foil? I've never heard of this before. Do you mean cling film?

Also I am selling a few swords on the swap forum!

Jens Nordlunde · 29th January 2018, 06:57 PM

Yes, cling film, but have a look at it from timer to time.
Be caraful how you treat the blade after it is all done. Make sure it is well sealed.

10th October 2017, 05:11 PM	#1
shastardhari Member Join Date: Oct 2017 Posts: 28	cleaning up a wootz tulwar Dear VIking sword forum, I recently purchased a tulwar for £43, once i had it in my hands i noticed a pattern throughout the length of the blade, crystaline wootz? i am currently cleaning it up with wd40 and fine wire wool... some bits are very stubborn and will not come off the blade, can some suggest what else I can use to clean the blade up , and if i do use various grits of wet and dry sandpaper how can I etch the pattern back? here are some images of the tulwar attached Attached Images

10th October 2017, 08:20 PM	#2
shastardhari Member Join Date: Oct 2017 Posts: 28	I used wd40 and fine wire wool to clean the blade, this is the result, what does everyone think? Attached Images

16th November 2017, 07:02 PM	#6
shastardhari Member Join Date: Oct 2017 Posts: 28	Dear all Thank you for your input. I have cleaned the tulwar as much as I could have with the use of fine wire wool then 1200_2500 wet and dry paper. Etched using Ferric chloride. Please tell me what you think of the end result. Attached Images

25th January 2018, 08:40 PM	#9
mariusgmioc Member Join Date: Sep 2014 Location: Austria Posts: 1,903	Hello, I believe that in order to get rid of all the pitting you would have to polish off half of the blade. So leave the pitting as it is since is not very detracting and it also serves as an indication to the age of the blade. You did a good job cleaning and etching the blade. Last edited by mariusgmioc; 26th January 2018 at 08:24 AM.

10th October 2017, 10:45 PM	#3
Jens Nordlunde Member Join Date: Dec 2004 Location: Europe Posts: 2,718	Welcome to the forum. What you could try is, to take some kitched issue spray it with WD40 and wrap it around the blade, then add some plastic foil, and leave it foe a day or two. Next time you photograph, please use a neutral background. Good luck.

10th October 2017, 11:49 PM	#4
Kmaddock Member Join Date: May 2014 Location: Ireland Posts: 543	Hi Welcome to the forum I find diesel v good at penetrating rust, leave soak for a while and then clean Here is a thread I posted a while back on etching, if you use the search forum you will find loads more information http://www.vikingsword.com/vb/showth...hlight=Etching Your sword looks v good and I hope the cleaned sword looks even better Regards Ken

12th October 2017, 06:41 PM	#5
mariusgmioc Member Join Date: Sep 2014 Location: Austria Posts: 1,903	More information at the link below: http://www.vikingsword.com/vb/showthread.php?t=21732

22nd November 2017, 04:58 PM	#7
Jens Nordlunde Member Join Date: Dec 2004 Location: Europe Posts: 2,718	I think the result have cocme out fine. I know the question, when cleaning and etching is an issue the question pops up, should I stop, or should I go further, but only the one who owns the weapons can answer that question.

29th January 2018, 06:57 PM	#12
Jens Nordlunde Member Join Date: Dec 2004 Location: Europe Posts: 2,718	Yes, cling film, but have a look at it from timer to time. Be caraful how you treat the blade after it is all done. Make sure it is well sealed.