indian rusty kattar, work in progress

francantolin · 30th May 2018, 10:29 PM

Hello everybody,
I finally received my kattar dagger,
it was all rusty,
I started to gently remove rust with vinegar,
for the blade ist's ok and nice pattern under the rust !!!

for the hilt-guard not really ... I have to try something else...
or will you leave it like that ??

What do you think ?

Kind regards

francantolin · 30th May 2018, 10:31 PM

francantolin · 30th May 2018, 10:34 PM

...

Jens Nordlunde · 30th May 2018, 10:52 PM

Ok, hold the blade, nice blade by the way:-), hit the side guards gently against wood - what do you hear?
If you hear like a tuning fork, it is made in one piece, but if you hear nothing, the blade and the hilt were likely made in two pieces, and put together.

NavdeepBal · 31st May 2018, 04:48 AM

Quote:

Originally Posted by francantolin

Hello everybody,
I finally received my kattar dagger,
it was all rusty,
I started to gently remove rust with vinegar,
for the blade ist's ok and nice pattern under the rust !!!

for the hilt-guard not really ... I have to try something else...
or will you leave it like that ??

What do you think ?

Kind regards

I haven’t quite seen a pattern like that. Might have been heavily acid etched fairly recently.

francantolin · 31st May 2018, 09:02 AM

Hello Jens,
Visually I think that it is made of two parts but when I tried you ''trick'' it still sounds like a bell.

For the pattern, maybe it is a recent blade on an old handle but I really don't think it can be acid etched,
for remove the rust, I scratch at least 1mm on the blade surface
after the soft acetic acid bath.
the pattern would disappear or be reduced with this treatment but it is clearly present and enhanced on the side of the blade too.

30th May 2018, 10:29 PM	#1
francantolin Member Join Date: Sep 2014 Posts: 877	indian rusty kattar, work in progress Hello everybody, I finally received my kattar dagger, it was all rusty, I started to gently remove rust with vinegar, for the blade ist's ok and nice pattern under the rust !!! for the hilt-guard not really ... I have to try something else... or will you leave it like that ?? What do you think ? Kind regards Attached Images

30th May 2018, 10:31 PM	#2
francantolin Member Join Date: Sep 2014 Posts: 877	Attached Images

30th May 2018, 10:34 PM	#3
francantolin Member Join Date: Sep 2014 Posts: 877	... Attached Images

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

30th May 2018, 10:52 PM	#4
Jens Nordlunde Member Join Date: Dec 2004 Location: Europe Posts: 2,718	Ok, hold the blade, nice blade by the way:-), hit the side guards gently against wood - what do you hear? If you hear like a tuning fork, it is made in one piece, but if you hear nothing, the blade and the hilt were likely made in two pieces, and put together.

31st May 2018, 09:02 AM	#6
francantolin Member Join Date: Sep 2014 Posts: 877	Hello Jens, Visually I think that it is made of two parts but when I tried you ''trick'' it still sounds like a bell. For the pattern, maybe it is a recent blade on an old handle but I really don't think it can be acid etched, for remove the rust, I scratch at least 1mm on the blade surface after the soft acetic acid bath. the pattern would disappear or be reduced with this treatment but it is clearly present and enhanced on the side of the blade too.