Ethnographic Arms & Armour
 

Go Back   Ethnographic Arms & Armour > Discussion Forums > Ethnographic Weapons
FAQ Calendar Today's Posts Search

Reply
 
Thread Tools Search this Thread Display Modes
Old 19th September 2009, 09:09 PM   #1
Jeff D
Member
 
Jeff D's Avatar
 
Join Date: Dec 2004
Location: B.C. Canada
Posts: 473
Question Sandblasting a Sword?

Hi all,

Has anyone here tried sand blasting a heavily rusted sword? I have a few projects which are heavily corroded which I would like to try it on. I have in the past tried the usual iron wool, oil and time, but, I find that it doesn't get the oxide out of the pits and grooves which could be hiding markings.
I will show a trial run I made on a old rusty square. It seems to work fairly quick. I would appreciate any tips and/or advice.

Thanks Jeff
Attached Images
  
Jeff D is offline   Reply With Quote
Old 19th September 2009, 09:22 PM   #2
Atlantia
Member
 
Atlantia's Avatar
 
Join Date: Jun 2008
Location: The Sharp end
Posts: 2,928
Default

Results look similar to vinegar de-rusting.

But I guess a damn site quicker!
Atlantia is offline   Reply With Quote
Old 20th September 2009, 09:05 AM   #3
kronckew
Member
 
kronckew's Avatar
 
Join Date: Mar 2006
Location: Room 101, Glos. UK
Posts: 4,178
Default

purists would not like the removal of the patina that has taken ages to develope, and consider a piece devalued if so treated; but if you must, i'd try glass bead blasting. it's less likely to remove precious metal and is a bit more delicate and less abrasive than sharp sand. still, it's better than taking an angle grinder to it.
kronckew is offline   Reply With Quote
Old 20th September 2009, 03:49 PM   #4
Jeff D
Member
 
Jeff D's Avatar
 
Join Date: Dec 2004
Location: B.C. Canada
Posts: 473
Default

Thanks Kronckew,

I used 30-60 crushed glass on the square above, and I think it is too aggressive to use on a sword. I will experiment with the glass beads next. In this thread ( http://www.vikingsword.com/vb/showth...t=sandblasting ) it was suggested to use coal slag 'black beauty', wouldn't that be more aggressive than crushed glass? Has any one used it?

Atlantia, the appearance is very similar to a vinegar etch, with a flat dull grey appearance to the metal. I think that is more a result on the oxidation below the original rust in this case? You are also right that the result took only a few seconds and is actually more controllable than a vinegar etch.

Thanks
Jeff
Jeff D is offline   Reply With Quote
Old 20th September 2009, 04:37 PM   #5
G. McCormack
Member
 
G. McCormack's Avatar
 
Join Date: Jul 2005
Location: Tallahassee, FL
Posts: 131
Default

maybe you could try a lighter medium, like walnut shells?
G. McCormack is offline   Reply With Quote
Old 20th September 2009, 05:07 PM   #6
kronckew
Member
 
kronckew's Avatar
 
Join Date: Mar 2006
Location: Room 101, Glos. UK
Posts: 4,178
Default

having read the post no. 4, i was about to also suggest ground up walnut shells, the cutter i served on had two Solar 1000 HP gas turbine engines (as well as two 1500 HP diesels), and we would occasionally have to clean the crud off the blades, we'd slowly dump a sack of ground walnut shells in the air intake. worked a treat. nice smoke and sparks out the stern exhausts too!

other forms of shells were tried, but walnut worked the best and was the least destructive.


glass bead blasting, a less intensive form of shot blasting, can also increase the surface hardness of the metal slightly due to the compression of the metal in the teeny dimples created by the impact, where sharp abrasives are more likely to cut away material.

you can also get plastic beads for even more benign bead blasting crud removal. linky on available mtls.

Last edited by kronckew; 20th September 2009 at 05:31 PM.
kronckew is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 07:37 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Posts are regarded as being copyrighted by their authors and the act of posting material is deemed to be a granting of an irrevocable nonexclusive license for display here.