![]() |
![]() |
#1 |
Member
Join Date: Nov 2010
Location: Wirral
Posts: 1,204
|
![]()
A new acquisition . This cutlass appears to be a British 1814 Pattern but the guard is a narrow dish type rather than the 'figure of eight' . The grip is ribbed iron and the blade has a narrow fuller and is stamped 'GR' with crown. Blade length ( across the curve ) is 24 inches ( 61 cm ) .
|
![]() |
![]() |
![]() |
#2 |
Member
Join Date: Mar 2012
Location: In the wee woods north of Napanee Ontario
Posts: 391
|
![]()
Very nice cutlass. Don't see many of the earlier ones. Earlier blade type than the later blades that were like the Baker bayonet blades.
You see this fullered blade on early 1700's infantry sidearms. |
![]() |
![]() |
![]() |
#3 | |
Member
Join Date: Nov 2010
Location: Wirral
Posts: 1,204
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
#4 |
Arms Historian
Join Date: Dec 2004
Location: Route 66
Posts: 9,896
|
![]()
This looks like one for Cap'n Mark Eley!!!!
What does Gilkerson have to say on these? I would have been inclined to agree with the private purchase variant idea but for the GR. |
![]() |
![]() |
![]() |
#5 |
Arms Historian
Join Date: Dec 2004
Location: Route 66
Posts: 9,896
|
![]()
Could not find Gilkerson, but Neumann ("Swords and Blades of the American Revolution", 1973) #364.S, has a cutlass with this heavy type blade dating 1740-60 at 19"; there is no marking, but the wide blade with radiused hatchet type point is identified American/European.
#376.S is an English cutlass with similar heavy blade (26") and marked to ship The Thomas of Selby on both the sheet steel guard and blade (dated 1770-1800). It is noted these type blades seen on English cutlasses into early 1800s. Perhaps this is a prototype for the 'figure 8'? The ribbed iron grips were used of course on customs and other civil service groups, but unsure if these would have had the crowned GR. |
![]() |
![]() |
![]() |
#6 |
Member
Join Date: Feb 2014
Posts: 86
|
![]()
Fine looking cutlass, congrats. My friend just picked up one of the nicest US 1860? one
|
![]() |
![]() |
![]() |
#7 |
Member
Join Date: Jan 2013
Location: Scotland
Posts: 327
|
![]()
Nice cutlass. Remember this thread back in 2013 on machetes - it discussed the GR used by commercial makers and shows some 19th century catalogues for cutlasses and machetes. One is reprinted from Gilkerson.
http://www.vikingsword.com/vb/showth...549#post163549 regards, CC |
![]() |
![]() |
![]() |
#8 |
Member
Join Date: Jan 2013
Location: Scotland
Posts: 327
|
![]()
According to Gilkerson the cast iron handle with 18 ribs and 6 vertical grooves first appeared on the Brit 1804 cutlass. The handle was almost straight.
Later versions of the handle are more shaped with a swelling and slight curve at the end to fit in the hand better. The 1830's coastguard cutlass is an example. And this one - courtesy of Cap'n Mark. http://www.vikingsword.com/vb/showthread.php?t=12145 The straight handle on yours would tend to indicate nearer the early part of the century. The 1814 appears with both types of handle. But for a cutlass that did not go into production there are an awful lot of examples. I believe most of these were private purchase using blades similar to those shown in the catalogues (see above post) some of which were marked with GR. Which, I think, is why you sometimes see what appears to be an 1814 blade with a hilt that is much less than the double disk. regards, CC. |
![]() |
![]() |
![]() |
Thread Tools | Search this Thread |
Display Modes | |
|
|