Dha-Lwe average measurements please

[Antonio Cejunior]

Hi everyone,

I would be very grateful if some of you gentlemen could provide me with the
average measurements of a Dha-lwe blade similar to this HOS #250



I am most interested in having the measures of:
a- the width of the blade taken just about the junction with the handle
b- the width of the blade at the "tip" (which is square)
c- the blade's spine thickness

Any other comments would be very much appreciated.
The blade's length is 51 cm or 20.08 inches so if you have a similar blade shape with different lengths, I would very much appreciate your input including the blade's length as the square tip flaring width may vary.

Thank you all.
Best regards,

Antonio

[Andrew]

Now, I wonder why Antonio needs such measurements....

I don't currently own any of this configuration, but I do have some square-tipped examples that don't flare so much. Would you want those?

[Mark]

Hi Antonio,

Did you check my web site? This dha is on there, but it was an early one, so it might not have the spine widths (I changed the format of the specification section). I'll take some measurements.

I have a couple of this style that are smaller - this one is unusually large and heavy. The proportions stay generally constant, handle-to-blade ratio, spine taper, etc. The taper is very dramatic, reducing by at least half over the first third of the blade length, and reaching essentially the width of the edge at the tip of the blade. PUFF, and others of our Thai collegues, call this a "double taper," as the rate of decrease is greater near the blade than it is approaching the tip, like the profile of the Eiffel Tower. Widths at the base of the blade are typically from round 3 to around 5 mm. This one is especially broad.

The span of the tip (edge to spine, in other words), does vary. This one is at the wide end of the scale. Many reach the maximum span around the last third of the blade.

[Antonio Cejunior]

Originally Posted by Mark

Hi Antonio,

Did you check my web site? This dha is on there, but it was an early one, so it might not have the spine widths (I changed the format of the specification section). I'll take some measurements.

I have a couple of this style that are smaller - this one is unusually large and heavy. The proportions stay generally constant, handle-to-blade ratio, spine taper, etc. The taper is very dramatic, reducing by at least half over the first third of the blade length, and reaching essentially the width of the edge at the tip of the blade. PUFF, and others of our Thai collegues, call this a "double taper," as the rate of decrease is greater near the blade than it is approaching the tip, like the profile of the Eiffel Tower. Widths at the base of the blade are typically from round 3 to around 5 mm. This one is especially broad.

The span of the tip (edge to spine, in other words), does vary. This one is at the wide end of the scale. Many reach the maximum span around the last third of the blade.

Hi Mark,
No I haven't gone to your page. I felt that possibly if I could get some "custom measurements" they would be kind of more accurate.
You mean a 20 inches blade for this type of blade is long and that heavy?
Even with the long handle?
I would've have thought otherwise

Thank you for describing the taper. I follow you. I wouldn't have thought that the taper was so dramatic. I wonder it it could say almost constant as a way to reinforce the last third. You know, like a Japanese hira-zukuri section, an elongated inverted triangle.

Yup, would very much appreciate the specific measurements asked
Plan to have one custom made. And the handle measurement would be excellent if you would be so kind to add to the measurements.

Grazzie tanti

[kronckew]

hi antonio,

here's mine, a bit less decorative but functional. tip is not quite square at the bottom
as the tip is sharpened all the way around to the spine. the spine has decorative diagonal cuts
and brass or copper inlays for the 1st 17 cm. from the grip.



hilt is 24 cm. long, 2.9 cm dia. at the pommel,
flaring to 3.5 cm. at the blade junction

blade is 47 cm. from the grip to tip, stub tang is 9cm.
and is 2x1 cm at the junction

blade at the grip is 2.7 cm. wide, spine 1 cm.

at 10 cm from grip, blade is 2.7 cm wide, spine 8 mm

at 20 cm, blade 3 cm, spine 3 mm

at 30 cm, blade 3.3 cm, spine 2.5 mm.

at 40 cm., blade is 3.6 cm, spine 2 mm

at 47 cm. blade is 4 cm., spine 2 mm.

[Antonio Cejunior]

Hello Kronckew,

Thank you very much for your most valuable help. It is most kind of you

Originally Posted by kronckew

hi antonio,

here's mine, a bit less decorative but functional. tip is not quite square at the bottom
as the tip is sharpened all the way around to the spine. the spine has decorative diagonal cuts
and brass or copper inlays for the 1st 17 cm. from the grip.



hilt is 24 cm. long, 2.9 cm dia. at the pommel,
flaring to 3.5 cm. at the blade junction

blade is 47 cm. from the grip to tip, stub tang is 9cm.
and is 2x1 cm at the junction

blade at the grip is 2.7 cm. wide, spine 1 cm.

at 10 cm from grip, blade is 2.7 cm wide, spine 8 mm

at 20 cm, blade 3 cm, spine 3 mm

at 30 cm, blade 3.3 cm, spine 2.5 mm.

at 40 cm., blade is 3.6 cm, spine 2 mm

at 47 cm. blade is 4 cm., spine 2 mm.

[Antonio Cejunior]

Originally Posted by Andrew

Now, I wonder why Antonio needs such measurements....

I don't currently own any of this configuration, but I do have some square-tipped examples that don't flare so much. Would you want those?

Ahh, Andrew,

I would like to custom order one
And so I need the specs.
Anyones you have would be welcomed. Specially if you add a picture and length to see the flaring ratio.

Many thanks