![]() |
|
![]() |
#1 |
Member
Join Date: Dec 2006
Location: Philly
Posts: 72
|
![]()
Now that I made you say that 3 times fast, I realy do have an inquiry. I came across a few nice pieces of iron and I wanted to attemp to make myself a replica spear to go with the rawhide shield I made last year. How are the blades attached to the shaft? I can tell the blade is tanged, but what actually secures the blade? Do they use some sort of glue, or is it the bindings? What kind of wood is the shaft made from?
|
![]() |
![]() |
![]() |
#2 |
Member
Join Date: Dec 2004
Location: What is still UK
Posts: 5,769
|
![]()
One of the ways is to shrink wrap with tubular animal tissue. Metal wire weave and rattan like material is also used. I have to say I think the animal parts is best reflecting the cattle based economy. I have not added the whole picture of this spear as it is not a true Iklwa but the fixing is the same.
|
![]() |
![]() |
![]() |
#3 |
Member
Join Date: Dec 2006
Location: Philly
Posts: 72
|
![]()
Thanks Tim! I was thinking along those lines. I was gonna cut some barbs into the tang, heat it red hot, then insert it into the shaft. I was gonna make a sleeve from the left over rawhide to cover it with. I might wire wrap for decorative purposes. I've tried wire wrapping before, but I just can't get the tension I want.
|
![]() |
![]() |
![]() |
#4 |
Member
Join Date: Dec 2006
Location: Philly
Posts: 72
|
![]()
Tim, taking second look at your spear, there seems to be a wrapped binding under the top layer. I think I will wrap the shaft in leather cord beford I cover it in the hide sleeve.
|
![]() |
![]() |
![]() |
#5 |
Member
Join Date: Dec 2004
Location: What is still UK
Posts: 5,769
|
![]()
The ribbing does not seem to be formed by binding under the animal tissue. As I said this is not an Iklwa. This spear is to the north and east, I believe as far as the Kenya Sudan border regions but essentially the same fixing as the classic Iklwa. The ribbing is tool worked like the baldric on this Seme. The Iklwa is not worked. Somebody will have an example to show, all mine have gone. Here is the spear it total-
http://www.vikingsword.com/vb/showth...turkana+shield |
![]() |
![]() |
![]() |
#6 |
Member
Join Date: Jan 2006
Location: Kent
Posts: 2,653
|
![]()
Hi,
I have mounted a genuine Zulu spearhead to a replacement shaft....copying one of their techniques. Drill a smaller diameter hole (slightly smaller than the tang) into the end of the shaft (as deep as you need.... full or half 'tang' length.) If you can obtain a cow tail cut a suitable length (slightly longer than the depth of the tang) with a diameter around the same size as the shaft.....slightly smaller is much better) Remove the bone and tissue without damaging the skin. You could at this stage leave it somewhere where it would remain dry but allow access to ants ......Yes ants ... they will clean remaining residue and are excellent little 'workers' ![]() Heat the tang to a reddish colour and insert into the drilled hole (use leather gloves) it will burn into the wood. Remove and repeat until the tang is at the required depth. Remove spearhead. The wet leather tube is then placed/pulled over the shaft. At the same time reheat the tang and force the spearhead into the shaft. Ensure the tube is in the correct position, (often some of the tang is partly covered in leather) and then allow to dry slowly. The leather will shrink and tighten .......once fully dry trim the edges with a sharp knife/scalpel. Use a wax later to seal the wood and leather. Hope this helps or gives you some ideas Kind Regards David |
![]() |
![]() |
![]() |
|
|