An interesting Cutlass

thinreadline · 18th February 2017, 04:16 PM

A new acquisition . This cutlass appears to be a British 1814 Pattern but the guard is a narrow dish type rather than the 'figure of eight' . The grip is ribbed iron and the blade has a narrow fuller and is stamped 'GR' with crown. Blade length ( across the curve ) is 24 inches ( 61 cm ) .

Will M · 18th February 2017, 07:30 PM

Very nice cutlass. Don't see many of the earlier ones. Earlier blade type than the later blades that were like the Baker bayonet blades.
You see this fullered blade on early 1700's infantry sidearms.

thinreadline · 18th February 2017, 09:03 PM

Quote:

Originally Posted by Will M

Very nice cutlass. Don't see many of the earlier ones. Earlier blade type than the later blades that were like the Baker bayonet blades.
You see this fullered blade on early 1700's infantry sidearms.

Yes it does have an early looking blade but it is closest to the Pattern 1814 cutlass which featured this type post 1803 ribbed iron hilt and had a short curved blade unlike its straight bladed P1804 predecessor .... however the guard is different to the P 1814 which had the same figure of eight ( double disc ) hilt as the P 1804. Its a puzzle to me . If it wasnt for the GR crown I would say it was a commercial variant.

Jim McDougall · 19th February 2017, 04:16 AM

This looks like one for Cap'n Mark Eley!!!!
What does Gilkerson have to say on these? I would have been inclined to agree with the private purchase variant idea but for the GR.

Jim McDougall · 19th February 2017, 04:33 AM

Could not find Gilkerson, but Neumann ("Swords and Blades of the American Revolution", 1973) #364.S, has a cutlass with this heavy type blade dating 1740-60 at 19"; there is no marking, but the wide blade with radiused hatchet type point is identified American/European.

#376.S is an English cutlass with similar heavy blade (26") and marked to ship The Thomas of Selby on both the sheet steel guard and blade (dated 1770-1800). It is noted these type blades seen on English cutlasses into early 1800s.

Perhaps this is a prototype for the 'figure 8'? The ribbed iron grips were used of course on customs and other civil service groups, but unsure if these would have had the crowned GR.

Terry K · 19th February 2017, 04:33 AM

Fine looking cutlass, congrats. My friend just picked up one of the nicest US 1860? one

CutlassCollector · 19th February 2017, 01:23 PM

Nice cutlass. Remember this thread back in 2013 on machetes - it discussed the GR used by commercial makers and shows some 19th century catalogues for cutlasses and machetes. One is reprinted from Gilkerson.

http://www.vikingsword.com/vb/showth...549#post163549

regards, CC

18th February 2017, 04:16 PM	#1
thinreadline Member Join Date: Nov 2010 Location: Wirral Posts: 1,204	An interesting Cutlass A new acquisition . This cutlass appears to be a British 1814 Pattern but the guard is a narrow dish type rather than the 'figure of eight' . The grip is ribbed iron and the blade has a narrow fuller and is stamped 'GR' with crown. Blade length ( across the curve ) is 24 inches ( 61 cm ) . Attached Images

18th February 2017, 07:30 PM	#2
Will M Member Join Date: Mar 2012 Location: In the wee woods north of Napanee Ontario Posts: 391	Very nice cutlass. Don't see many of the earlier ones. Earlier blade type than the later blades that were like the Baker bayonet blades. You see this fullered blade on early 1700's infantry sidearms.

19th February 2017, 04:16 AM	#4
Jim McDougall Arms Historian Join Date: Dec 2004 Location: Route 66 Posts: 9,943	This looks like one for Cap'n Mark Eley!!!! What does Gilkerson have to say on these? I would have been inclined to agree with the private purchase variant idea but for the GR.

19th February 2017, 04:33 AM	#5
Jim McDougall Arms Historian Join Date: Dec 2004 Location: Route 66 Posts: 9,943	Could not find Gilkerson, but Neumann ("Swords and Blades of the American Revolution", 1973) #364.S, has a cutlass with this heavy type blade dating 1740-60 at 19"; there is no marking, but the wide blade with radiused hatchet type point is identified American/European. #376.S is an English cutlass with similar heavy blade (26") and marked to ship The Thomas of Selby on both the sheet steel guard and blade (dated 1770-1800). It is noted these type blades seen on English cutlasses into early 1800s. Perhaps this is a prototype for the 'figure 8'? The ribbed iron grips were used of course on customs and other civil service groups, but unsure if these would have had the crowned GR.

19th February 2017, 04:33 AM	#6
Terry K Member Join Date: Feb 2014 Posts: 86	Fine looking cutlass, congrats. My friend just picked up one of the nicest US 1860? one

19th February 2017, 01:23 PM	#7
CutlassCollector Member Join Date: Jan 2013 Location: Scotland Posts: 330	Nice cutlass. Remember this thread back in 2013 on machetes - it discussed the GR used by commercial makers and shows some 19th century catalogues for cutlasses and machetes. One is reprinted from Gilkerson. http://www.vikingsword.com/vb/showth...549#post163549 regards, CC