Another question about etching

ariel · 18th July 2010, 08:48 PM

I have been using a new bottle of the RadioShack etching fluid ( ferric chloride), diluted ~1:5. Took a soft cloth, soaked it, passed in a single movement over the blade (polished, washed, dried, alcohol defatted), and after ~10 seconds, washed it with copious amount of water , then sodiuim bicarbonate, then water again and dried it. From the beginning to the end it took no more than 1 min.
I got a wootz pattern ( pretty feeble), but the entire blade became grey.
What should I do to:
1. Enhance the pattern? More concentrated etcher? Longer exposure?
2. Eliminate the grey color? Rub it with rough felt?

kai · 19th July 2010, 12:52 AM

Hello Ariel,

Please post a pic or 2...

Is the blade expected to be wootz?

Regards,
Kai

Battara · 19th July 2010, 03:32 AM

Also what kind of water - distilled I hope? Did you also use baking soda afterward?

Ferguson · 19th July 2010, 11:33 AM

I've had wootz blades that didn't respond well to FeCl. They used nitric in the past I think. I've never used it. Very dangerous stuff.

Steve

ariel · 19th July 2010, 02:16 PM

Thanks to all!
Both blades are unquestionable wootz: very weak pattern seen.
Yes, distilled.
Yes, baking soda ( sodium bicarbonate)
What %% nitric acid? How long?

And, if the rest of the blade is still grey, any rubbing afterwards or some other method?

Gavin Nugent · 19th July 2010, 03:17 PM

Quote:

Originally Posted by ariel

Thanks to all!
Both blades are unquestionable wootz: very weak pattern seen.
Yes, distilled.
Yes, baking soda ( sodium bicarbonate)
What %% nitric acid? How long?

And, if the rest of the blade is still grey, any rubbing afterwards or some other method?

Ariel,

You speak the lingo and will find this a help.

http://playground.sun.com/~vasya/Obach-01.html

It works for me and as noted, is very dangerous, I mean very, be careful.

Gav

18th July 2010, 08:48 PM	#1
ariel Member Join Date: Dec 2004 Location: Ann Arbor, MI Posts: 5,503	Another question about etching I have been using a new bottle of the RadioShack etching fluid ( ferric chloride), diluted ~1:5. Took a soft cloth, soaked it, passed in a single movement over the blade (polished, washed, dried, alcohol defatted), and after ~10 seconds, washed it with copious amount of water , then sodiuim bicarbonate, then water again and dried it. From the beginning to the end it took no more than 1 min. I got a wootz pattern ( pretty feeble), but the entire blade became grey. What should I do to: 1. Enhance the pattern? More concentrated etcher? Longer exposure? 2. Eliminate the grey color? Rub it with rough felt?

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

19th July 2010, 12:52 AM	#2
kai Member Join Date: Apr 2005 Posts: 3,254	Hello Ariel, Please post a pic or 2... Is the blade expected to be wootz? Regards, Kai

19th July 2010, 03:32 AM	#3
Battara EAAF Staff Join Date: Dec 2004 Location: Louisville, KY Posts: 7,225	Also what kind of water - distilled I hope? Did you also use baking soda afterward?

19th July 2010, 11:33 AM	#4
Ferguson Member Join Date: Dec 2004 Location: Kernersville, NC, USA Posts: 793	I've had wootz blades that didn't respond well to FeCl. They used nitric in the past I think. I've never used it. Very dangerous stuff. Steve

19th July 2010, 02:16 PM	#5
ariel Member Join Date: Dec 2004 Location: Ann Arbor, MI Posts: 5,503	Thanks to all! Both blades are unquestionable wootz: very weak pattern seen. Yes, distilled. Yes, baking soda ( sodium bicarbonate) What %% nitric acid? How long? And, if the rest of the blade is still grey, any rubbing afterwards or some other method?